Category:How to - Known Issues - Revision history

Ashcharles: /* Issues with prebuild overo images */

2016-04-01T21:10:59Z

‎Issues with prebuild overo images

Conor O'Rourke at 17:32, 29 March 2014

2014-03-29T17:32:22Z

Conor O'Rourke: Add duovero section

2014-03-29T17:31:16Z

Add duovero section

Msvilans at 17:11, 21 July 2010

2010-07-21T17:11:11Z

Msvilans at 17:10, 21 July 2010

2010-07-21T17:10:27Z

ManuelStahl: Add test of version 201004220807

2010-04-23T07:46:03Z

Add test of version 201004220807

ManuelStahl at 12:32, 19 April 2010

2010-04-19T12:32:30Z

ManuelStahl: Add "Issues with prebuild overo images"

2010-04-19T12:31:29Z

Add "Issues with prebuild overo images"

Sgarman: Created page with 'If you have fixed a problem while setting up your gumstix board that you feel other people are likely to encounter, please document your solution here. == Network Problems == '…'

2010-02-10T01:24:29Z

Created page with 'If you have fixed a problem while setting up your gumstix board that you feel other people are likely to encounter, please document your solution here. == Network Problems == '…'

New page

If you have fixed a problem while setting up your gumstix board that you feel other people are likely to encounter, please document your solution here.

== Network Problems ==

'''Symptom:''' Network services do not come up. LAN link lights blink for a couple of seconds during bootup, but then remain out. This has been observed with the connex board with the netCF expansion module running a fresh install of OpenEmbedded.

'''Solution:''' The file /etc/network/interfaces contains network interface definitions for several classes of devices. If you are not using the wireless ethernet expansion module, comment out the wlan0 interface section and reboot the unit.

@@ Line 24: / Line 24: @@
 == Issues with prebuild overo images ==
-Images are here: http://www.sakoman.com/feeds/omap3/glibc/images/overo/
+Images are here: https://www.gumstix.com/software/software-downloads/
 === Overo fire with Palo35 ===

@@ Line 16: / Line 16: @@
 == Issues with prebuilt DuoVero images ==
-The serial port on Uart2 is /dev/ttyO1. This is interfered with by the Bluetooth systemd service which isn't necessary on this board. Disable this systemd service to get access to /dev/ttyO2.
+The serial port on Uart2 is /dev/ttyO1. This is interfered with by the Bluetooth systemd service which isn't necessary on this board. Disable this systemd service to get proper access to /dev/ttyO1.
 <tt>systemctl disable bluetooth</tt>

← Older revision		Revision as of 17:31, 29 March 2014
Line 13:		Line 13:

	'''Solution:''' The solution is documented here: [[Overo Tobi Ethernet]].		'''Solution:''' The solution is documented here: [[Overo Tobi Ethernet]].
		+
		+	== Issues with prebuilt DuoVero images ==
		+
		+	The serial port on Uart2 is /dev/ttyO1. This is interfered with by the Bluetooth systemd service which isn't necessary on this board. Disable this systemd service to get access to /dev/ttyO2.
		+
		+	<tt>systemctl disable bluetooth</tt>
		+
		+	and rebooting is a good start.

	== Issues with prebuild overo images ==		== Issues with prebuild overo images ==

@@ Line 10: / Line 10: @@
 ===Wired Ethernet Does Not Come Up===
-'''Symptom:''' When booting an Overo with Tobi expansion board, the wired Ethernet eth0 interface does not come up. No IP address is acquired via DHCP, even though eth0 is configured to use DHCP. The solution is [[[Overo Tobi Ethernet|documented here]].
+'''Symptom:''' When booting an Overo with Tobi expansion board, the wired Ethernet eth0 interface does not come up. No IP address is acquired via DHCP, even though eth0 is configured to use DHCP.
 == Issues with prebuild overo images ==

@@ Line 15: / Line 15: @@
 {| border="0" cellpadding="2" cellspacing="1" style="background:#e2e2e2;" class="sortable wikitable"
 !  Version      || Bootup  || Login   || LCD     || Touchscreen
 |- bgcolor="#f8f8ff"
 |  201004141106 || {{Yes}} || {{Yes}} || {{No}}  || {{No}}

@@ Line 2: / Line 2: @@
 == Network Problems ==
 '''Symptom:''' Network services do not come up. LAN link lights blink for a couple of seconds during bootup, but then remain out. This has been observed with the connex board with the netCF expansion module running a fresh install of OpenEmbedded.
@@ Line 7: / Line 9: @@
 '''Solution:''' The file /etc/network/interfaces contains network interface definitions for several classes of devices. If you are not using the wireless ethernet expansion module, comment out the wlan0 interface section and reboot the unit.
 == Issues with prebuild overo images ==

← Older revision		Revision as of 12:31, 19 April 2010
Line 6:		Line 6:

	'''Solution:''' The file /etc/network/interfaces contains network interface definitions for several classes of devices. If you are not using the wireless ethernet expansion module, comment out the wlan0 interface section and reboot the unit.		'''Solution:''' The file /etc/network/interfaces contains network interface definitions for several classes of devices. If you are not using the wireless ethernet expansion module, comment out the wlan0 interface section and reboot the unit.
		+
		+
		+	== Issues with prebuild overo images ==
		+
		+	Images are here: http://www.sakoman.com/feeds/omap3/glibc/images/overo/
		+
		+	=== Overo file with Palo35 ===
		+	{\| border="0" cellpadding="2" cellspacing="1" style="background:#e2e2e2;" class="sortable wikitable"
		+	! Version \|\| Bootup \|\| Login \|\| LCD \|\| Touchscreen
		+	\|- bgcolor="#f8f8ff"
		+	\| 201004141106 \|\| {{Yes}} \|\| {{Yes}} \|\| {{No}} \|\| {{No}}
		+	\|- bgcolor="#f8f8ff"
		+	\| 201002031857 \|\| {{Yes}} \|\| {{Yes}} \|\| {{Yes}} \|\| {{Yes}}
		+	\|}