Difference between revisions of "GPIO"
| Line 4: | Line 4: | ||
| − | * 3.3V | + | * Logic level (3.3V) signals |
* 3-4mA max | * 3-4mA max | ||
| Line 20: | Line 20: | ||
<br> | <br> | ||
<br> | <br> | ||
| + | |||
| + | |||
| + | == Accessing GPIO's from userland == | ||
| + | |||
| + | |||
| + | If proc-gpio is a module, add it to /etc/modules or do a modprobe proc-gpio. | ||
| + | |||
| + | A number of files exist under /proc/gpio, one for each GPIO on the PXA processor. | ||
| + | |||
| + | If you cat one of these files, you get, eg: | ||
| + | <pre> | ||
| + | # cat /proc/gpio/GPIO12 | ||
| + | 12 GPIO in set | ||
| + | </pre> | ||
| + | |||
| + | That tells you — GPIO number, function (either GPIO, AF 1, AF 2, or AF 3), in|out, set|clear. | ||
| + | |||
| + | You can change any of those values, by writing to the file, eg: | ||
| + | <pre> | ||
| + | # echo "AF1 out" > /proc/gpio/GPIO12 | ||
| + | </pre> | ||
| + | |||
| + | This sets GPIO12 to AF1, out mode. (In the case of GPIO12, the PXA defines this function as putting out the 32kHz clock signal.) this is currently case-sensitive | ||
| + | |||
| + | If you have the GPIO set to an output, and GPIO mode, you can set or clear the signal: | ||
| + | <pre> | ||
| + | # echo "GPIO out set" > /proc/gpio/GPIO12 | ||
| + | # echo "GPIO out clear" > /proc/gpio/GPIO12 | ||
| + | </pre> | ||
| + | The alternative functions are described in the PXA255 Developer's Manual (link should be found in the Featured links-box) section 4.1.2. | ||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | gpio-event | ||
| + | |||
<br> | <br> | ||
<br> | <br> | ||
Revision as of 08:47, 10 April 2008
| GPIO( n ) |
- Logic level (3.3V) signals
- 3-4mA max
all GPIO's information and examples should go here
todo
According to the PXA270 datasheet:
http://pubs.gumstix.com/documents/PXA%20Documentation/PXA270/PXA270%20Electrical,%20Mechanical,%20and%20Thermal%20Specification%20%5b280002-005%5d.pdf
most of the pins are limited to 3mA, and a few can go upto 4 mA (see page 5-9)
Accessing GPIO's from userland
If proc-gpio is a module, add it to /etc/modules or do a modprobe proc-gpio.
A number of files exist under /proc/gpio, one for each GPIO on the PXA processor.
If you cat one of these files, you get, eg:
# cat /proc/gpio/GPIO12 12 GPIO in set
That tells you — GPIO number, function (either GPIO, AF 1, AF 2, or AF 3), in|out, set|clear.
You can change any of those values, by writing to the file, eg:
# echo "AF1 out" > /proc/gpio/GPIO12
This sets GPIO12 to AF1, out mode. (In the case of GPIO12, the PXA defines this function as putting out the 32kHz clock signal.) this is currently case-sensitive
If you have the GPIO set to an output, and GPIO mode, you can set or clear the signal:
# echo "GPIO out set" > /proc/gpio/GPIO12 # echo "GPIO out clear" > /proc/gpio/GPIO12
The alternative functions are described in the PXA255 Developer's Manual (link should be found in the Featured links-box) section 4.1.2.
gpio-event
Related pages on the old wiki:
http://docwiki.gumstix.org/index.php/GPIO_event
http://docwiki.gumstix.org/index.php/Tips_and_tricks#Access_GPIOs_from_user-space
http://docwiki.gumstix.org/index.php/Sample_code/C/gpregs
http://docwiki.gumstix.org/index.php/Kernel_programming
.
