Difference between revisions of "UARTs"
From Gumstix User Wiki
| Line 35: | Line 35: | ||
* Normally mapped to ttyS0 in the kernel and Y0 in some schematics | * Normally mapped to ttyS0 in the kernel and Y0 in some schematics | ||
* FFUART pins are located on the [[60pin connector|60-pin Hirose]] connector | * FFUART pins are located on the [[60pin connector|60-pin Hirose]] connector | ||
| + | * [http://www.gumstix.org/schematics/B00002-FFUART.png?nocache=1 Schematic diagram for the FFUART] | ||
<br> | <br> | ||
| Line 59: | Line 60: | ||
* Normally mapped to ttyS3 in the kernel and Y1 in some schematics | * Normally mapped to ttyS3 in the kernel and Y1 in some schematics | ||
* HWUART pins are located on the [[60pin connector|60-pin Hirose]] (Connex and Basix only) | * HWUART pins are located on the [[60pin connector|60-pin Hirose]] (Connex and Basix only) | ||
| + | * [http://www.gumstix.org/schematics/B00002-HWUART.png?nocache=1 Schematic diagram for the HWUART] | ||
<br> | <br> | ||
| Line 66: | Line 68: | ||
<br> | <br> | ||
| + | |||
| + | * [http://www.gumstix.org/schematics/B00003-FF_ST_UARTS.png?nocache=1 Schematic diagram for the STUART] | ||
| + | |||
<br> | <br> | ||
<br> | <br> | ||
Revision as of 09:08, 15 March 2008
- Logic level (3.3V) signals
- FFUART speeds to 230 kbps (normally mapped to ttyS0 in the kernel and Y0 in some schematics )
- HWUART speeds to 921 kbps (normally mapped to ttyS3 in the kernel and Y1 in some schematics)
- Both can use RxD, TxD, RTS, CTS.
- STUART speeds to 230 kbps (normally mapped to ttyS2)
- BTUART is not an exposed interface; mapped to ttyS1 by the kernel and connected physically to the bluetooth module if one is present.
- Note! Current kernels use ttyS3 (HWUART) for bluetooth. This is available on the BTUART pins by setting GPIO42 and 43 to AF3 - and this is the default configuration. This can be very confusing if you want to use the HWUART for something else! To re-enable HWUART on ttyS3, make bluetooth use ttyS1 (see /etc/default/bluetooth) and then set GPIO42 to AF1 in and GPIO43 to AF2 out. You can then set GPIO48 to AF1 out (HWUART TXD) and GPIO49 to AF1 in (HWUART RXD).
http://docwiki.gumstix.org/Gumstix_UARTs
Contents
UARTs
FFUART
| FF_CTS |
| FF_RTS |
| FF_TXD |
| FF_RXD |
- Logic level (3.3V) signals
- Speeds to 230 kbps
- Normally mapped to ttyS0 in the kernel and Y0 in some schematics
- FFUART pins are located on the 60-pin Hirose connector
- Schematic diagram for the FFUART
HWUART
| HW_CTS |
| HW_RTS |
| HW_TXD |
| HW_RXD |
- Logic level (3.3V) signals
- Speeds to 921 kbps
- Normally mapped to ttyS3 in the kernel and Y1 in some schematics
- HWUART pins are located on the 60-pin Hirose (Connex and Basix only)
- Schematic diagram for the HWUART
STUART
BTUART
| BT_CTS |
| BT_RTS |
| BT_TXD |
| BT_RXD |
| BT_NRESET |
- BTUART pins are located on the 60-pin Hirose and 24-pin flex ribbon (Verdex only) connectors.
- It is not an exposed interface; mapped to ttyS1 by the kernel and connected physically to the bluetooth module if one is present.
Related pages on the old wiki:
http://docwiki.gumstix.org/Gumstix_UARTs
http://docwiki.gumstix.org/Gumstix_motherboard_I/O#UART
http://docwiki.gumstix.org/Tips_and_tricks#UARTs
.
