Difference between revisions of "Category:How to - usb"
m (Added 2.6.32 reference) |
m (Formatting) |
||
Line 59: | Line 59: | ||
collisions:0 txqueuelen:0 | collisions:0 txqueuelen:0 | ||
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) | RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) | ||
− | + | ||
usb0 Link encap:Ethernet HWaddr D6:2C:8F:D9:51:32 | usb0 Link encap:Ethernet HWaddr D6:2C:8F:D9:51:32 | ||
BROADCAST MULTICAST MTU:1500 Metric:1 | BROADCAST MULTICAST MTU:1500 Metric:1 |
Revision as of 13:46, 20 January 2010
USBNet with Overo
The OTG USB port on the Overo expansion boards support USB networking. To enable this, the OTG port needs to be configured as a USB peripheral or gadget. The default kernels from Gumstix have the OTG port configured to act as a USB host.
The procedure for changing the configuration requires rebuilding your kernel, so you should first be comfortable with setting up a build environment and building images for your Overo.
The following steps assume you are using a recent snapshot of the gumstix-oe git tree and are going to use kernel version 2.6.31 or 2.6.32.
The gumstix-oe linux-omap3_2.6.xx recipes for either of these kernels has a variable that allows you to specify how you want the OTG usb port configured.
Kernel version 2.6.31 is used for the example. Substitute 2.6.32 if that's the kernel you are using.
To get started, first edit the recipe file ${OVEROTOP}/org.openembedded.dev/recipes/linux/linux-omap3_2.6.31.bb
Change the line
MUSB_MODE ?= "host"
to
MUSB_MODE ?= "peripheral"
or "otg".
Next rebuild your kernel.
cd ${OVEROTOP} bitbake -c clean linux-omap3-2.6.31 bitbake -c rebuild linux-omap3-2.6.31
And then rebuild your rootfs.
bitbake omap3-console-image
Change omap3-console-image to whatever image you use.
Once you have booted the new system, you still need to load the g_ether driver since it was built as a module.
You can add g_ether to /etc/modules if you always want it to load at boot.
root@overo# modbprobe g_ether g_ether gadget: using random self ethernet address g_ether gadget: using random host ethernet address usb0: MAC d6:2c:8f:d9:51:32 usb0: HOST MAC f2:99:dc:4c:cb:7a g_ether gadget: Ethernet Gadget, version: Memorial Day 2008 g_ether gadget: g_ether ready
root@overo:~# ifconfig -a lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) usb0 Link encap:Ethernet HWaddr D6:2C:8F:D9:51:32 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Configure the usb0 interface the way you would any other.
For example
root@overo:~# ifconfig usb0 192.168.20.2 netmask 255.255.255.0
If you then plug the usb OTG cable into a host computer ready for usb networking you'll get a console message
g_ether gadget: high speed config #1: CDC Ethernet (ECM)
The rest is all standard Linux networking.
Pages in category "How to - usb"
The following 3 pages are in this category, out of 3 total.