Difference between revisions of "Category:How to - i2c"

From Gumstix User Wiki
Jump to: navigation, search
(Added a Sample code section and one link)
Line 70: Line 70:
  
 
Another source of I2C information can be found [http://www.gumstix.net/wiki/index.php?title=I%C2%B2C here].
 
Another source of I2C information can be found [http://www.gumstix.net/wiki/index.php?title=I%C2%B2C here].
 +
 +
==Sample code==
 +
 +
[http://github.com/scottellis/overo-blinkm Controlling BlinkM leds over I2C using a Gumstix Overo]
  
 
[[Category:How_to_-_general]]
 
[[Category:How_to_-_general]]

Revision as of 07:44, 20 November 2009

Background

I2c is a 2-wire serial 8 bit communications protocol from the old days. It is mainly used to communicate between on-board components when the design does not allow for a data and address bus. Typical components are elapsed timer chips, ee-proms, FRAM's, A/D and D/A chips. Some cpu's have the I2c hardware shift registers built in.

The 2 wires are the SCL or clock wire and the SDL or data wire. The clock high to low transition is used to signal that the data wire has a stable 1/0 data value and that the receiver should shift this into the data results register. The clock line is high when the bus is idle. A special high to low transition on the clock line followed by a high to low transition on the data line signals the start of a message sequence. the end of a message sequence is a low to high transition in the data line followed by a low to high transition in the SCL line. An important aspect of this communication standard is that each device is assigned a unique 7 bit address, (oh yea the 8th bit is the Read/write indicator to complete the byte). The device address is the first byte sent in any communication. Subsequent bytes of a message depend on the device you are talking to.

Because of patents that have since expired, other companies had to use slightly differnet ways to do the same thing so a very similar serial communicatinos method called SPI uses 4 wires and another called TWI uses the same 2 wires.

I2C with Gumstix Overo

There are several i2c busses available on the overo board.

The one accessible from the 40 pin expansion board headers is i2c-3.

Pin 23 is SCL and Pin 24 is SDA.

The voltage levels are 1.8v, so a voltage level shifter is required to connect to 3.3 or 5 volt slave devices.

The overo main board already has pullup resistors for SCL and SDA.

The default gumstix kernels set the i2c-3 bus speed to 400 kHz.

This can be changed to 100 kHz with a kernel command line parameter in u-boot

i2c_bus=3,100

or by modifying ../git/arch/arm/mach-omap2/board-overo.c and rebuilding the kernel.

The i2c-3 bus appears as a character device under /dev

root@overo:/dev# ls -all i2c*
crw-rw---- 1 root root 89, 1 Jan  1  2000 i2c-1
crw-rw---- 1 root root 89, 3 Jan  1  2000 i2c-3

Programmers can access devices on the bus using standard unix file i/o.

You must set the slave address with an ioctl() call prior to communicating with a slave device.

The driver takes care of shifting the slave address one bit and appending the R/W bit in the first byte of the transfer.

Here's a C example minus any error checking.

...
#include <stdint.h> 
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <linux/i2c.h> /* for I2C_SLAVE */
 ...
int fh;
uint8_t data[4];
fh = open("/dev/i2c-3", O_RDWR);
/* tell the driver we want the device at address 0x20 */
ioctl(fh, I2C_SLAVE, 0x20);
/* write two bytes */
data[0] = 0x05;
data[1] = 0x08;
write(fh, data, 2);
/* read 4 bytes */
read(fh, data, 4);
close(fh);

Further information

Another source of I2C information can be found here.

Sample code

Controlling BlinkM leds over I2C using a Gumstix Overo

Pages in category "How to - i2c"

This category contains only the following page.