Category:SPI

From Gumstix User Wiki
Revision as of 06:46, 20 January 2011 by Sellis (Talk | contribs) (More details)

Jump to: navigation, search

Overo SPI

Kernel documentation for the SPI framework can be found in the Documentation directory of your linux source tree or here Documentation/spi/spi-summary.

Linux SPI drivers are broken into two parts. A controller driver that handles direct communication with the hardware and a protocol driver to handle the details of the data for a particular device. The interface defined in spi.c/spi.h is the bridge between the two.

For the OMAP3's, the controller driver is omap2_mcspi.c. The OMAP3's have 4 SPI busses which the omap2_mcspi driver handles. The kernel config option to include the omap2_mcspi driver is CONFIG_SPI_OMAP24XX and is already built into standard Gumstix Overo kernels.

The OMAP3 SPI controller has the ability to act as either a SPI master or SPI slave, but the current kernel code only supports the SPI master configuration.

Gumstix brings out SPI bus 1 chip select pins 0 and 1 on most of the Overo expansion boards.

Protocol Drivers

A protocol driver is what you need to use the SPI system on Linux.

There are a couple of steps that need to happen.

  1. Slave devices must be registered for each SPI bus and chip select position used.
  2. A protocol driver needs to be registered with the system using the same name as the devices it will be handling so the kernel can link the two.

It doesn't matter which order these steps are performed. Most existing SPI drivers do the device registration completely outside the driver code in a board file. If you are writing your own driver, it is probably more convenient to do it in the driver code itself. When both device and driver registration are completed, the probe() function for the protocol driver will be called and SPI communications can start.

SPI data communication happens using I/O queues. One or more SPI transfers are bundled up into SPI messages in the protocol driver. The protocol driver then submits the SPI messages to the controller driver's I/O queue. These messages are then processed asynchronously by the controller driver in FIFO order. As each message finishes, the controller notifies the protocol driver via a callback function.

There are some synchronous helper functions exposed by the interface to simplify the asynchronous behaviour of the Linux SPI system for protocol driver writers.

Spidev

Spidev is a standard Linux module that implements a generic SPI protocol driver while exposing a char device interface to userland.

The documentation for spidev can be found here - Documentation/spi/spidev.

The spidev driver does not register devices so a board file patch like this one spidev-enable.patch is required to use spidev with the Overos. You should customize that patch for the particular device you are using. Things you might want to change are the bus speed and the mode.

The spidev driver is built in to the standard Overo kernels.

Only one protocol driver at a time can manage a particular CS line on a given SPI bus.

As you can see from the above patch, the standard Overo kernels already have devices registering for SPI bus 1 CS0 (ADS7846 touchscreen controller) and SPI bus 1 CS1 (LGPHILIPS LB035Q02 display driver). You will have to disable one or both of these drivers in your kernel config if you want to use that respective CS line.

If you are using OE, apply the board patch by copying it to the org.openembedded.dev/recipes/linux/linux-omap3-2.6.xx/ directory and then adding a line to include the patch in your kernel recipe org.openembedded.dev/recipes/linux/linux-omap3_2.6.xx.bb

There are more detailed instructions for getting spidev working on an Overo on the 'Writing a Linux SPI driver' link below.

You can also search the Gumstix mailing list archives for spidev

Custom Driver

Here is an article that can get you started writing your own custom SPI driver for Linux using Gumstix Overos as the example board - Writing a Linux SPI driver

This category currently contains no pages or media.